Audio Innovate INNOFADER Custom VCA Crossfader for Pioneer DJM350/DJM400

This Item Has Been Discontinued
Or Is No Longer Available.

This information only remains here as a reference
for those who need information on this product.

Planet DJ is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com

audio innovate innodjm400
audio innovate innodjm400 Audio Innovate INNOFADER Custom VCA Crossfader for Pioneer DJM350/DJM400
This is a special Innofader model designed to work with the DJM-400, as well as the newer DJM-350. No other adpaters are required.

This model can also be used for all of the mixers which work with the original Innofader. Just beware that the wiring on the adapter J4 cable is reversed and you'll need to reverse it back to its original wiring to work normally.

INSTALLATION INSTRUCTIONS:
First to start remove the screws as shown here. Note that the next few pictures have the Innofader at the crossfader; on the DJM-400 it will have the original fader installed. Sorry I was lazy here. Bear with me.


Once you remove all of the faceplate screws, you should be able to pop off the faceplate. Lift up the faceplate slightly and remove the flat cable shown here:


For ease of installation, lift the faceplate up, flip over to the left, and place down as shown here:


Remove the 2 screws on the front panel shown here. The crossfader plate should then drop down. Also make sure to disassemble the crossfader from the fader plate by removing the 2 mounting screws. All of the screws you need to remove here have red circles around them.


Before mounting the Innofader, prepare it as below. First mount the Innofader to the large bracket using the 6mm insulated flathead screws and insulated washers. Please read the instructions for insulating the Innofader from the mixer first.


Mount the tab to the Innofader with the 2 hex screws and 2 lock washers. Use a 2.5mm hex wrench to tighten the screws. While you are installing these screws, hold the Innofader body as shown in the picture. This will maximize the distance between the top screw and the bracket and eliminate any potential rubbing.


Connect the 6-pin crossfader cable to the Misc Adapter Board connecter J13 "NUMARK DIGITAL". Note the connector housing is already removed because the Pioneer cable header won't fit. This is completely normal and a special modification we did just for this product. Install the crossfader cable with the white wire closest to the blue Innofader cable wire.


Disconnect the Innofader cable from the Innofader itself and connect to the Misc Adapter Board. As shown in the picture, the misc adapter board blue wire goes to the Innofader grey wire and vice versa. But the green wires and yellow wires still match.

NOTE: There is a batch of Innofaders which have the holes drilled upside down. In this case when you assemble the Innofader to the plate as shown in this picture, the label will be facing down rather than up. No worries...

If the label is facing up, the wire connections between the Innofader cable and adapter board are as follows:

BLUE <-> GREY
GREEN <-> GREEN
YELLOW <-> YELLOW
GREY <-> BLUE

If the label is facing down, the wire connections between the Innofader cable and adapter board are as follows:

BLUE <-> GREY
GREEN <-> YELLOW
YELLOW <-> GREEN
GREY <-> BLUE

We released a small number of faders with the label facing down where the green and yellow wires are swapped. If this is the case, please use the mini-screwdriver included with the Innofader to swap these wires as shown here (different connector but same idea)



Place the Insulator tube over the Misc Adapter board and Innofader cable, and connect the Innofader cable back to the Innofader.


Place the Innofader with the bracket in the correct position on the Pioneer fader plate.


Screw the Innofader with the bracket down to the Pioneer fader plate using the 8mm flathead screws included with the Innofader. Plug the flat cable back into the fader plate PC board. Make sure you tape down the insulator securely to keep a safe distance from power supply components in the Pioneer DJM-400. Note: I was a bit lazy in this picture. Use more tape to be safe!


Put the faceplate back on the mixer and screw the front panel screws back into the fader plate. Note the drawing shows the screws only partially installed; make sure later to fully tighten the screws.


Screw the faceplate screws back into the fader plate. Note the drawing shows the screws only partially installed; make sure later to fully tighten the screws.


Finally install the remaining faceplate screws


And you're done!

Additional Information

UPCN/A
SKUINNODJM400
ManufacturerAudio Innovate
Product ConditionNew - On Clearance
ReturnableNo

Write Your Own Review

You're reviewing: Audio Innovate INNOFADER Custom VCA Crossfader for Pioneer DJM350/DJM400

How do you rate this product? *

 1 star2 stars3 stars4 stars5 stars
Quality