for Instant VIP Discounts on most gear! (Better Than Codes, and it's Free)

QSC PL-2.0HV Powerlight Amp

qsc pl-2.0hv
Images may show accessories or configurations not packaged with this item.

Be the first to review this product

Unavailable Discontinued or no longer available.
Sorry, this item is discontinued or no longer available from us. We've left this page up for reference only. Check out some of the other great alternatives on this page or click below to see if it can still be found elsewhere.
Buy on Amazon
The amplifier contain two independent amplifier channels and a switching power supply.


The amplifier shall contain all solid-state circuitry, using complementary silicon output devices. The amplifier shall exceed the efficiency of an ordinary class-B linear output circuit. The amplifier shall operate from 50-60 Hz AC power. The amplifier shall operate from a 15A 120 V AC outlet, drawing less than 1150 VA when driven with random program material at 1/8 rated power into four ohm loads. The amplifier shall be supplied with a single molded AC cord having a standard NEMA 15 AC plug for 120 V units; 220-240 V units shall be equipped 320-C19 16A IEC mains connector and a removable power cord. The amplifier shall comply with FCC part 15 class B requirements.

The amplifier shall employ forced-air cooling with two variable speed fans for minimum acoustic noise. Air flow shall be from rear to front to avoid temperature rise inside the rack. Rack mounting shall be possible without clearance between amplifiers for ventilation. The amplifier shall be capable of continuous operation at 1/3 power, into eight ohm loads, in ambient temperatures up to 104F (40C).

The amplifier shall contain two independent amplifier channels and a switching power supply. All amplifier protection systems shall be self-resetting upon removal of fault. Each channel shall have protective circuitry against short circuit or mismatched loads. Each channel shall monitor heat sink temperature and shall trigger fan speed boost, and if necessary, signal muting to prevent excessive temperature rise. Both channels shall have synchronized on-off muting, acting for three seconds after turn-on, and within 1/4 second after turn-off or loss of AC power. Each channel shall have DC fault protection for the load, consisting of a power supply shutdown. Each channel shall have a user-defeatable clip limiter.

The front panel shall contain the AC power switch; a green LED power-on indicator; a yellow LED standby indicator and a red protect mode indicator. Each channel shall have the following controls and displays: A front panel detented gain control, with 11 gain settings: 36 dB, 34 dB, 32 dB, 30 dB, 28 dB, 26 dB, 24 dB, 22 dB, 18 dB, 14 dB, -x; a recessed front panel clip limiter defeat switch; a green signal present LED triggering at -30 dB; two yellow LED output indicators, triggering at -20 dB and -10 dB; a red LED showing true amplifier clipping.

The output connectors for each channel shall be a "touch-proof" binding posts, accepting banana plugs or up to 7 AWG (4 mm dia.) wire. Connector terminals are arranged to allow bridge mono connection.

The rear panel input shall provide barrier strip and Neutrik "Combo" connectors for each channel. The XLR input shall be wired with pin 2 high, the 1/4" TRS input shall be wired with tip positive, ring negative, and sleeve grounded. Inputs shall be electronically balanced, with a minimum impedance of 10 kilohms per side, and a common mode rejection of at least 50 dB from 20 Hz to 20 kHz.

A high density 15 Pin Data Port connector shall carry both audio and amplifier operational status signals to and from a QSC MultiSignal Processor.

Switches shall be provided for stereo-bridging and parallel inputs. A two position barrier strip, on the rear panel, shall be used for remote Power Supply Enable; a contact closure shall place both the amplifier channels in standby mode, when the front panel power switch is in the on position. The front panel power switch shall function as a master switch that removes all AC power.

Each channel shall be capable of meeting the following performance criteria with both channels driven: Sine-wave output power of 400 watts into sixteen ohms, and 650 watts into eight ohms, 20 Hz to 20 kHz, with less than 0.1% THD. Frequency response at 3 dB below rated power shall be 20 Hz to 20 kHz within 0.15 dB. The voltage gain shall be 63, equivalent to 36 dB, and the input sensitivity shall be 1.16 Vrms. The signal to noise ratio over the range of 20 Hz to 20 kHz shall exceed 108 dB relative to full output. IHF damping factor shall exceed 350.

The amplifier chassis shall occupy two rack spaces, with provision for securing the rear corners. Depth from mounting surface to tips of rear supports shall be 17.9" (45.5 cm).

Weight shall not exceed 18 lbs. (8.2 kg.). The amplifier shall be the QSC Audio Products PowerLight

Additional Information

Product ConditionNew - On Clearance

QSC PL-2.0HV Powerlight Amp Reviews

How do you rate this product? *

 1 star2 stars3 stars4 stars5 stars