Crown MA12000I MacroTech Power Amplifier

Not In Stock Not In Stock, But We'll Order It In For You
This item is not in stock, but can usually be back in our warehouse within 4 to 10 days, depending upon stock levels at Crown's warehouse. This time frame is not guaranteed, rather an estimate based on historical data. Order now! We'll notify you promptly if we hear of any delay.
Free Shipping FREE Ground Shipping to the contiguous U.S. (details)
$7,413.68
Affirm Financing
    • BONUS! Buy Now and Earn 5000 PDJ Bucks ($50.00)! MUST Be Logged In! Domestic U.S. customers only. Exact value may vary once logged in.
The Crown Macro-Tech i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else

Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less wasteRugged construction ensures that all Macro-Techs are built to withstand years of abuse on the roadGlobal Power Supply designed to deliver maximum power no matter what country you work inBuilt-in load, line voltage, input and output monitoringStandard Ethernet networking via System Architect lets system operators monitor and control the amplifier from any locationPerformance Frequency Response (at 1 watt, 20Hz - 20 kHz into 8 ohms) 0.25 dB Signal to Noise Ratio below rated full-bandwidth power, A-weighted > 108 dB Total Harmonic Distortion (THD) at 1 watt into 8 ohms <0.1% Total Harmonic Distortion (THD) Plus Noise at full rated power < 0.35%, 20 Hz to 20 kHz Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to -30 dB < 0.35% Damping Factor (20 Hz to 100 Hz at 8 ohms) > 5000 Crosstalk (below rated power, 20 Hz to 1 kHz) > 80 dB Common Mode Rejection (CMR) (20 Hz to 1 kHz) > 55 dB, typically > 70 dB DC Output Offset (Shorted input) < 3 mV Input Impedance (nominal) 10 kilohms balanced, 5 kilohms unbalanced Maximum Input Level +20 dBu typical Load Impedance (Note: Safe with all types of loads) Stereo: 1/2/4/8/16 ohms Bridge Mono: 2/4/8 ohms Input Sensitivity (referenced to 8 ohm rated output)1.4V, 32 dB gain, and 26 dB gain Voltage Gain (referenced to 8 ohm rated output)MAi-12000i: 39.3 dB to 24.5 dB Required AC Mains Universal AC input, 100-240VAC 50/60 Hz (15%). Maximum AC mains voltage 264VAC. AC Line Connector Five cordsets supplied with amplifier (USA, UK, European, Australia, India) Construction Cooling Dual-zone, microprocessor controlled, continuously variable speed fans, front-to-back airflow Front Panel Cast aluminum with integrated handles. Weight 28 pounds (12.7 kg) net, 36 pounds (16.3 kg shipping. Dimensions (W x H x D) 19 in. (48.3 cm) W x 3.5 in. (8.9 cm) H x 16.2 in. (41.1 cm) D. Protection Amplifier is protected against reactive loads, faults and shorts. If one channel experiences a catastrophic failure, the entire amplifier will shut down. Guaranteed minimum power in watts at 20 Hz-20 kHz with 0.35% THD. 5,900W (20 mS burst, 2-ohm dual per ch.), 3,500W (20 Hz-20 kHz, 2-ohm dual per ch.), 3,500W (1 kHz, 2-ohm dual per ch.) 4,000W (4-ohm dual per ch.) 2,100W (8-ohm dual per ch.) 7,000W (4-ohm bridge) 8,000W (8-ohm bridge)

Additional Information

UPCN/A
SKUMA12000I
ManufacturerCrown
Product ConditionNew
ReturnableYes

Write Your Own Review

You're reviewing: Crown MA12000I MacroTech Power Amplifier

How do you rate this product? *

 1 star2 stars3 stars4 stars5 stars
Quality